Remote Monitoring
Systems
24/7 supervision of unmanned sites
STC-704 Four Zone Wireless
Environmental Monitoring System in outdoor enclosure
|
The STC-704 Wireless Environmental Monitoring System provides
off-site monitoring of four parameters, plus A.C. power
loss, daily communication test, low battery and "restore
to normal" conditions. Two web-controllable relays
are included for interfacing to on-site equipment where
a 5 amp dry contact can be used. LEDs display all power
and input conditions.
The equipment is contained in a weatherproof ABS enclosure
for outdoor or indoor mounting. There is a 3/4 and 1/2
inch conduit opening in the enclosure to permit wire entry.
A 16VAC plug-in transformer to power the STC-704 and 7AH,
12 volt rechargeable battery are supplied for backup power,
providing continuous operation during power failures up
to 48 hours. An internal temperature compensated power
supply keeps the standby battery at optimum charge with
rapid, current limited and voltage float charging. A low
battery disconnect circuit removes the battery from the
system on an extended power outage to avoid deep discharging
of the battery.
All inputs are buffered through selectable one minute
or one second delay to "Alarm" and one minute
or one second delay to "Normal". This eliminates
the momentary signals generated by power fluctuations,
rapid photocell operation and switchover transients. Each
input can be selected for N.C. or N.O. input for "Normal" condition.
Compression terminals are provided for all wiring. Any
size wire, up to 12ga, may be used for the power and monitored
device connections. |
Click here to
view specifications.
- 4 zones plus power fail and low battery.
- Wireless reporting no phone line needed.
- Weatherproof Case
- Monitors 4 inputs plus power failure
- Daily Signal Check
- 2 remote controllable relays
|
Features
- Wireless Reporting-no phone line needed
- Units can monitor any physical parameter that can be measured.
- AC powered with 12 volt rechargeable lead-acid battery
- During a power failure the standby battery provides power to
the control panel for at least 24 hours to continue to report
conditions at the site.
- Daily Signal tests to ensure reliability of each unit.
The STC-704 Remote
Monitoring System can be customized
at the factory for special
requirements.
Typical Applications
Agricultural
Presence or absence of water in tanks,
irrigation systems, etc.
Monitor fuel levels in equipment
Monitor water pressure and flow
Oil & Gas Monitoring
Pipeline Monitoring
Power Fail/Restart
Remote Restart
Injection Well Monitoring
Tank Levels
|
Boats & Vacation Homes
AC/power loss
Bilge Connection
High Water
Low Battery
Freeze
Flood
Environmental/Industrial
Freezers
Coolers
Water Storage
Water Levels
Temperature
HVAC
Water Flood
Hazardous Gas
|
Elements of Remote Monitoring
Detection
Our Wireless Remote Monitoring Units have inputs to monitor up
to 4 parameters plus it supervises for A/C power fail and monitors
it's own standby power battery in addition to sending a daily
communications test signal.
Our Landline Remote Monitoring Units have inputs to monitor up
to 4, 8, or 24 parameters, plus supervise for A/C power fail
and monitor it's own standby power battery in addition to sending
a daily communications test signal.
If you have unique needs, ask us. We can help and we will make modification during manufacture.
Reporting
Sends important signals directly to your cell phone, email, or
pager.
If centrally monitored it comes to our 24/7 monitoring center
.
Response
For instance if you are monitoring
for power and there is a power fail an alert will be sent within
a few minutes.
You can have your own response according to what signal you receive,
or have our Central Monitoring notify the correct people according
to the signal type.
Accessories
External Antenna for Uplink or other GSM/CDMA Transmitters
STC 1010 Fiberglass GSM Omni-Directional Antenna
- Increase signal strenth
- Increase reliability
- Easy to mount
- Includes mounting hardware, tie-wraps, instructions
7DB gain omni-directional antenna for use with
any GSM transmitter. Easy mounting on conduit or uni-strut. Cable
length allows use of full 10ft. mounting material for maximum elevation.
Cable is prefitted with SMA connector to match Digi-Cell GSM/CDMA
Units. Directly fits Uplink Digi-Cell and Ademco 7845 units.
Antenna Accessories:
Adaptor for Tellular units (TNC male to SMA female)
Extension Cables
12 ft Extension Cable
6.5 ft. Extension Cable
Battery Testers
STC 612 Battery Analyzer
Comparison
of STC 612 & STC
4110 Battery Analyzers |
| Battery Analyzers |
STC 612 |
STC 4110 |
| Microprosessor Controlled |
Yes |
Yes |
| Host Powered |
Yes |
Yes |
| Input Voltage from Battery |
5-16 VDC |
5-16 VDC |
| Testing Range |
2-12 amphour |
4-110 amphour |
| Tests |
| Standby Charged Condition |
Yes |
Yes |
| Dynamic Capabilities under load |
Yes |
Yes |
| Remaining Amphour Capacity |
No |
Yes |
| Battery Temperature |
No |
Yes |
| Voltmeter Function |
No |
Yes |
Why wait for a low battery signal?
Include battery testing with scheduled maintenance and improve
system reliability.
This battery analyzer performs automated
dynamic load tests on standard lead acid batteries commonly
used in burglar alarm systems, fire alarm panels and emergency
lighting systems. This product is microprocessor controlled
for accurate bbnhb and repeatable results. Pre-load voltage
and dynamic load tests are conducted for standard amp-hour
rated batteries. To operate, simply connect the battery to
the tester and select the correct amp hour test. The STC-612
analyzer then displays the final battery condition - good,
marginal, or bad. This unit tests 6 and 12 volt batteries.
The tester is enclosed in a rugged die-cast aluminum enclosure
with a strong polycarbonate graphic overlay. It is designed
for field or bench use.
Typical Applications
- Security System Backup Batteries
- Security Alarm Batteries
- UPS Power Backup Batteries
- Fire Alarm System Batteries
Black Hinged Carrying Case
Replacement/Additional Leads |
STC 4110 Dual Mode Battery Analyzer
The ultimate in battery analysis, this DUAL
MODE BATTERY ANALYZER is ideal for those requiring unquestioned
accuracy. Microprocessor controlled and host powered, the
STC 4110 is designed to test and evaluate the standby charged
condition and dynamic capabilities under load of any 6V or
12V, sealed, lead-acid battery. It will also give the remaining
amp-hour capacity.
FEATURES
Amp hour range of 4 to 100 A.H.
Copper conductor & alligator clips
Thermo laser gun
Weather Proof Case
48" HIGH-FLEX instrumentation cable
Automatically determines voltage of battery
Unit measures 8"L x 5"H x 11"W
Weighs 10 lb.
Typical Applications
- Emergency lighting systems
- Propulsion Batteries
- Communication Batteries
- Fire alarm systems
- Integrated security systems
- Communication systems
- To verify State-of-Charge of new and
stock batteries
- To verify emergency system minimum operating
times
- To verify capability of operating backup
systems
- Optimized Performance via Battery Matching
- Propulsion systems
- UPS uninterruptible power systems
- Airborne applications
- Wherever batteries are utilized
- Allows technician to quickly determine
condition of battery to produce its rated power
Specifications
- Input Voltage: 5-15VDC
- Testing Range: 4-110AH (12V), 4-40AH
(6V)
- Load Current: 130mA (static test), up
to 30 amps (dynamic test)
- Dynamic Load Interval: 60 seconds
- Input Connection: Military Spec-97 Series
Connector Set
- Operating Tempatures: 32 F-140 F
- Dimensions: Length 8", Height 5",
Width 11"
- Weight: 10 lbs
|
